Ag-leader Versa Users Manual User Manual Page 1

Operators ManualFirmware Version 5.4Ag Leader PN 4002722 Rev. G

x Firmware Version 5.4Legend Setup... 170ApplicationLiqu

86 Firmware Version 5.4Select the controller make and modelSelect Generic if implement is not included in list.The rest of the steps will follow th

87 SETUPAGFINITISETUPAGFINITICONNECTING TO WI-FI NETWORKInsert USB Wi-Fi Adapter to USB port of the display.To connect to a Wi-Fi network:Press: Ho

88 Firmware Version 5.4One or more networks are in range but display is not configured to connect to a network.Connected to network. Green bars rep

89 SETUPAGFINITIFILE TRANSFERFile Transfer requires a File Transfer license (one per display). AgFiniti is compatible with Ag Leader Integra and Ve

90 Firmware Version 5.4AgFiniti tab shows AgSetup and AgData files that are present in the AgFiniti account. From the AgFiniti tab, select file and

91 SETUPAGFINITIExports AgData files by growerExports AgData files by eventExports AgData files each time display is shut down if logged into AgFin

92 Firmware Version 5.4IMPORTING A VARIETY REFERENCE MAP (HARVEST ONLY)from Options screen in the Event WizardPress the “Select Event” button and f

93 SETUPAGFINITIAllows remote viewer to view display screens without display user having to give permissionPress: Home button > AgFiniti button

94 Firmware Version 5.4

95 GPS GPSGPSGPS BUTTONDuring your field operation, the GPS (satellite) button in the upper left-hand side of the Status Bar should appear as green

xi TABLE OF CONTENTSServo Control Valve Settings (By Manufacturer) ...198Liquid Servo Settings Description.

96 Firmware Version 5.4• Note: If using OmniSTAR, see “OmniSTAR Settings” on page 97.• Differential SourceSelect choice of WAAS/EGNOS, Satellite (

97 GPSOMNISTAR SETTINGSOmniSTAR (Differential Source drop-down menu)Press: Home button > Setup (wrench) button > GPS button > Receiver Set

98 Firmware Version 5.4• FrequencyIn the Frequency drop-down list box, select the geographic region where you are located. If you wish to enter a C

99 GPSNote: The use of OmniSTAR® differential requires purchase of a subscription from OmniSTAR. Settings related to using satellite differential

100 Firmware Version 5.4The Serial Port Settings screen is the place where you can adjust GPS output. The appearance of the Serial Port Settings sc

101 GPS- ASAP represents a Hz value of more than 1.• NMEA MessagesThese checkboxes represent various communication protocols or formats that have b

102 Firmware Version 5.4• GPS Speed• Position RateThe frequency that the receiver is sending the display your position in longitude and latitude (G

103 GPS• Correction AgeThe length of time since the GPS receiver has obtained its last update.Note: The age of the DGPS corrections (as delivered

104 Firmware Version 5.4• Receiver ID• Firmware Version• Serial Number• e-Dif Subscription• GLONASSGPS INFORMATION - OMNISTAR TABPress: GPS (satell

105 GPSGPS INFORMATION - NTRIP or Press: GPS (satellite) button > GeoSteer tab or ParaDyme• NTRIP ConnectConnects the display to the NTRIP corre

xii Firmware Version 5.4Controller Settings: Direct Injection Pump Calibration... 223Pump Calibration Setting...

106 Firmware Version 5.42500 RTK SETUPPress: Home button > Setup (wrench) button > GPS button > Receiver Setup (wrench) button• Differenti

107 GUIDANCE GUIDANCEGUIDANCEGUIDANCE/STEERING CONTROLSETUPPress: Home button > Setup (wrench) button > GPS button • Manual GuidanceSelect th

108 Firmware Version 5.4LIGHTBAR SETTINGSSETUPPress: Home button > Setup (wrench) button > GPS button > Lightbar Settings button• LED Spac

109 GUIDANCENEW PATTERNSTRAIGHTSelect PatternPress: Map button > Guidance tab (in Mapping Toolbox) > New Pattern button > Straight Pattern

110 Firmware Version 5.4Patterns are automatically saved when the B point is set (A point for A+ pattern). For more information see “AutoSave” on p

111 GUIDANCE• Press to mark point B. The AB line appears on the map screen and point B is marked with a red ball.Note: Guidance extends beyond t

112 Firmware Version 5.4Press: Map button > Guidance tab (in Mapping Toolbox) > New Pattern button > Identical Curve Pattern SelectionSyst

113 GUIDANCESelect PatternPress: Map button > Guidance tab (in Mapping Toolbox) > New Pattern button > Pivot Pattern SelectionSystem defau

114 Firmware Version 5.4• Shift By DistanceThis sets the field edge as the distance and direction in relation to the AB Line created. In the Pivot

115 GUIDANCEPress . You will automatically return to the Map screen.Inputting Paths into SmartPathAB ManagerPress: Map button > Guidance tab (in

xiii TABLE OF CONTENTSLinear Actuator/Clutch Settings...253 Actuator/Clutch Logic...

116 Firmware Version 5.4 As you continue using the SmartPath, the map screen will display three lines:• (A) The Base Path Appears as a black line,

117 GUIDANCETo adjust this setting, press the Guidance Options button on the Guidance Tab. The Guidance Options screen appears. Press the Smart Tab

118 Firmware Version 5.4MANAGE PATTERNSSPATIAL SORTPress: Map button > Guidance tab (in Mapping Toolbox) > New Pattern buttonSpatial Sort all

119 GUIDANCEREMOVE PATTERN/REMOVE ALL PATTERNSTo remove a pattern from the display memory, first press the Manage Patterns button on the Guidance T

120 Firmware Version 5.4The Pattern Cycle Button allows the user to easily cycle between patterns with a single button press. Patterns will cycle i

121 GUIDANCEPAUSEPress: Map button > Guidance tab (in Mapping Toolbox) > Setup (wrench) button > Pause buttonThe Pause button allows your

122 Firmware Version 5.4 Nudge allows you to adjust the swaths by a specified distance.Small Nudge (single arrow) shown on left.Large Nudge settin

123 GUIDANCEShift moves all of the swaths by a specified distance to the left or right, (including the AB line). The swaths can be shifted by a dis

124 Firmware Version 5.4Motor Aggressiveness — determines how aggressively the motor engages.Heading Aggressiveness — determines how aggressively t

125 GUIDANCE• Paths Between Tramlines - use to enter the number of passes between tramlines.• Paths to Start Field - use to enter the number of

xiv Firmware Version 5.4Load Configuration... 278Manual Moi

126 Firmware Version 5.4

127 GUIDANCEONTRAC2+GUIDANCEONTRAC2+To ensure proper AutoSteer Operation make sure your GPS source is setup properly.Complete the following steps t

128 Firmware Version 5.4To return to the previous screen, press the Back icon. Press the Back icon from the AutoSteer Setup screen to return to you

129 GUIDANCEONTRAC2+The Control Point of a vehicle is defined as:• Standard Wheeled Vehicle (MFWD, Floater, Sprayer) - Rear Axle• Track Vehicle - C

130 Firmware Version 5.4EDITSelect VehiclePress: Vehicle button > Manage Vehicle button > Select Vehicle > Edit buttonSelect the vehicle f

131 GUIDANCEONTRAC2+Export profile to a USB drive1. Insert a USB drive into the display.2. Select the vehicle you want to export, and press Expor

132 Firmware Version 5.4• OnTrac2 ECU Tilt Zero Measurements 1 and 2: The ECU has a tilt sensor in it to help take into account side hills and bump

133 GUIDANCEONTRAC2+5. When the vehicle's draw bar reaches the flag, stop the vehicle, place it in park, turn off the AutoSteer system, and e

134 Firmware Version 5.4STEERING COMPONENTSPress: Vehicle button > Steering ComponentsThis screen enables you to adjust steering components. The

135 GUIDANCEONTRAC2+3. Use the Steering Command buttons to send the various commands to the MDU. Observe that the steering wheel behaves according

1 GENERALABOUT THIS MANUALGENERALGENERALABOUT THIS MANUALINTRODUCTION AND COMPANY PROFILEABOUT USWelcome to the Ag Leader Technology family. Ag Lea

136 Firmware Version 5.4MANAGE SETTINGSPress: System button > Manage Settings buttonThe Manage Settings screen enables you to:• Save or delete t

137 GUIDANCEONTRAC2+DatabaseThe database contains all the vehicle and system parameter data required for system operation. A backup of the database

138 Firmware Version 5.4The Accessories menu is used to activate or deactivate optional sensors. Currently only the remote engaged switch is availa

139 GUIDANCEONTRAC2+• GPS Mode parameter — current GPS mode of the receiver.• PDOP (Positional Dilution of Precision) — measure of the strength of

140 Firmware Version 5.4

141 TILLAGETILLAGETILLAGECREATE TILLAGE CONFIGURATIONPress: Home button > Setup (wrench) button > Configuration (tractor) button > Configu

142 Firmware Version 5.4The Configuration Setup screen appears. The appearance of this screen will vary depending upon your particular operating co

143 TILLAGE • (A) GPS Status• (B) Total Field Acres• (C) Ground Speed• (D) Diagnostics button• (E) Map Legend• (F) Logging Status button• (G) Auto

144 Firmware Version 5.4

145 PLANTINGCREATE PLANTING CONFIGURATIONPLANTINGPLANTINGCREATE PLANTING CONFIGURATIONMost of the functionality of the display is not available unt

2 Firmware Version 5.4ph: (515) 232-5363fax: (515) 232-3595e-mail: support@agleader.comCAUTION: This display has an internal lithium coin cell batt

146 Firmware Version 5.47. Select Implement Options• Split Rows EnabledCheck this box to enable the display to log data from the planter’s Split R

147 PLANTINGCREATE PLANTING CONFIGURATION14. Select ImplementSelect Implement from drop-down menu.15. Select Planting Method16. Select Speed Sou

148 Firmware Version 5.4

149 PLANTINGAUTOSWATHPLANTINGAUTOSWATHROW SHUTOFFCreate an Implement configuration with Row Shutoff by following the procedure in “Create Planting

150 Firmware Version 5.4AUTOMATIC AUTOSWATH CONTROLPress: Home button > Setup (wrench) button > Configuration (tractor) button > Configura

151 PLANTINGAUTOSWATH• Turn-OnThis setting determines how far ahead the system looks to turn the sections back on. This setting compensates for del

152 Firmware Version 5.4FIXING OVERPLANTING AND UNDERPLANTING IN AUTOSWATHAutoSwath Function — Turn Off Look AheadProblem — UnderplantingRecommende

153 PLANTINGRATE CONTROLPLANTINGRATE CONTROLHYDRAULIC SEED RATE CONTROLThe Hydraulic Seed Control Module allows operators to control up to three hy

154 Firmware Version 5.4Channel Tab settings• Gear RatioRatio of the revolutions of the hydraulic drive as compared to one revolution of the seed m

155 PLANTINGRATE CONTROLControl Valve Settings - Servo• Valve Response 1Determines the speed of the servo valve when product control error exceeds

3 GENERALABOUT THIS MANUALUSB FLASH DRIVEDisplay kits include a USB Flash Drive which you can use to save and transfer your data in and out of the

156 Firmware Version 5.4HYDRAULIC SEED CONTROLLER SETTINGS FOR SPECIFIC PLANTERSNote: The settings, provided below, should be a good starting poin

157 PLANTINGRATE CONTROLHYDRAULIC SEED METER CALIBRATION NUMBERSPrior to calibrating the Hydraulic Seed Meter, the numbers that appear in the Meter

158 Firmware Version 5.4STEPPER SEED RATE CONTROLThe Stepper Seed Control module allows Rawson ACCU-RATE Variable Rate Controller to control up to

159 PLANTINGRATE CONTROLChannel Tabs• Max Meter SpeedThis number represents the maximum recommended RPM of the seed meter, and is specified by the

160 Firmware Version 5.4GEAR RATIO CALCULATIONS FOR SEED RATE MOTORSThe Gear Ratio is a setting that appears on the Controller Tab for the Stepper

161 PLANTINGRATE CONTROLGear Ratio Drawing - For Multiple Drive Combinations Seed Rate Drive Setting (Calculating a Gear Ration for Multiple Dri

162 Firmware Version 5.4Gear Ratio Drawing Shaft DrivesSeed Rate Drive Setting. Carry the Decimal place to the nearest 0.001 for accurate resul

163 PLANTINGRATE CONTROLSeed Ratio Calculation Example Procedure for Shaft DrivesThis example assumes a single drive motor. Step 5 notes that this

164 Firmware Version 5.4• Make sure seed meter is primed. For more information, See “Priming Seed Rate Meters” above.Press: Map button > Meter R

165 PLANTINGRATE CONTROLNote: The Rate buttons in the Product Control Toolbox at top right are explained in “Product Control Toolbox” on page 165.

4 Firmware Version 5.4product feature additions or enhancements. These optional software updates may have an additional fee associated with them.AU

166 Firmware Version 5.4• (J) Rate Setup buttonThe Rate Setup button opens the Rate Control Settings screen, described at “Rate Control Settings” o

167 PLANTINGRATE CONTROLSHOWING PRESCRIPTIONS ON THE MAP SCREENOn the Map screen’s Mapping Toolbox, press the Legend Setup (wrench) tool and the Le

168 Firmware Version 5.4d. Switch the Master Switch on.e. Press the up button one time. Now press the down button one time. The drive should be tur

169 PLANTINGPLANTINGPLANTING MAP SCREEN - ZOOM TO EXTENT • (A) GPS Status• (B) Total Field Acres• (C) On-screen Lightbar• (D) Ground Speed• (E) Dia

170 Firmware Version 5.4The Legend Setup button on the Map Legend Tab of the Mapping Toolbox opens the Legend Select screen.Use the drop-down menu

171 APPLICATIONLIQUID RATE CONTROLAPPLICATIONAPPLICATIONLIQUID RATE CONTROLDirectCommand allows the variable rate application of single or multiple

172 Firmware Version 5.49. Assign Container CapacityPress to enter the container capacity. Press to accept.10. Enter Container UnitsUse the d

173 APPLICATIONLIQUID RATE CONTROL20. Select Speed SourceUse drop-down menu to select Primary Source, set Backup Source, and configure Auxiliary C

174 Firmware Version 5.4Select Swath section to edit and press Edit button.Enter Offset for that specific section and Forward/Backward from rear ax

175 APPLICATIONLIQUID RATE CONTROLCREATING SINGLE PRODUCTS To create a single product, to be added to a product template or to be applied by itself

5 GENERALABOUT THIS MANUALLinks to web sites are shown in blue, italicized, and underlined text, as in the following example: To view the web site,

176 Firmware Version 5.4Note: Prior to making a new product template, it is recommended to add the individual products to the list in the units re

177 APPLICATIONLIQUID RATE CONTROL10. Enter Manufacturer name if applicable.- Manufacturer name can be added to the drop-down menu by pressing 11.

178 Firmware Version 5.43. Configure Product MixWhen using a product template, the mix contents and amounts are defined at the map screen by:-a.ac

179 APPLICATIONLIQUID RATE CONTROLMIX CALCULATORWhen a product template is setup using rate/area, the mix calculator can be used to show how much o

180 Firmware Version 5.4For product templates, select which products to make active within the template.Press calculator to access the Mix Calculat

181 APPLICATIONLIQUID RATE CONTROLThe Configuration Setup screen appears. Screen will vary depending on configuration. Process may include the foll

182 Firmware Version 5.4When using Hardi ISOBUS, Implement Modeling can be set to Hardi SafeTrack. This allows display to accurately calculate path

183 APPLICATIONLIQUID RATE CONTROL• Control Valve SettingsOpens the Control Valve Settings screen, which displays control valve settings for PWM, S

184 Firmware Version 5.4• PWM StandbyThis is a user-defined setting that determines the percent duty cycle the system uses when the booms are all o

185 APPLICATIONLIQUID RATE CONTROLFENCE ROW NOZZLE INDICATORSControl fence row nozzles through the DirectCommand system by mapping the switches in

Firmware Version 5.4

6 Firmware Version 5.4

186 Firmware Version 5.4APPLICATION MAP SCREEN - ZOOM TO DETAIL • (A) GPS Status• (B) Ground Covered• (C) Ground Speed• (D) Diagnostics button• (E

187 APPLICATIONLIQUID RATE CONTROLRATE CONTROL: PRODUCT CONTROL TOOLBOXDuring DirectCommand Run Time operations, the Product Tabs are shown in the

188 Firmware Version 5.4• Rate Increase and Decrease Arrows/ allow Product Application Rate to be changed according to the Target Rate Increment. I

189 APPLICATIONLIQUID RATE CONTROLRATE CONTROL: CONTAINER LEVELWhen filling or emptying container, use the Container Level portion of the Rate Cont

190 Firmware Version 5.4Tank AlarmsThe Container Alarm button, which appears at the bottom of the Container Level portion of the Rate screen, displ

191 APPLICATIONLIQUID RATE CONTROL2. The File Selection screen appears.3. Highlight the correct .AGSETUP (prescription) or .shp (shape) file and

192 Firmware Version 5.4The Rate Control Settings screen appears.1. Open File Selection screen.Press the Load Prescription button.2. The File Sel

193 APPLICATIONLIQUID RATE CONTROLCAUTION: Selection of the wrong data column or unit will result in misapplication of product.Note: The only time

194 Firmware Version 5.45. Make sure the implement cable is plugged in. If plugged in, then test for 12 volts on pins A and B.Problem: Boom indica

195 APPLICATIONLIQUID RATE CONTROLProblem: No boom pressure at the start of the field.Solution: Before product application begins, use manual val

7 GENERALINSTALLATIONGENERALINSTALLATIONDISPLAY HARDWARE • (A) USB media slotUsed for data transfer in and out of the display.• (B) speakerThe buil

196 Firmware Version 5.4JOHN DEERE SPECIFIC INSTRUCTIONSHere are some tips to remember when operating the display in conjunction with a SprayStar1

197 APPLICATIONLIQUID RATE CONTROLCONTROL VALVE SETTINGSLiquid Product Control Valve Configuration Options• Inline ServoRate control is achieved th

198 Firmware Version 5.4SERVO CONTROL VALVE SETTINGS (BY MANUFACTURER)Flow Control ValveControl Valve ConfigurationValve Response 1Valve Response 2

199 APPLICATIONLIQUID RATE CONTROLDickey-john NH3 Heat ExchangerIn-line Servo 40% 10% 8Flow Control Valve or Sprayer Model (and year if applicable)

200 Firmware Version 5.4Case IH 4260 with KZKCO valveNon-AIM Command Mode By-Pass Servo2% 40% 10% 5Case IH 3150 with Raven valveNon-AIM Command Mod

201 APPLICATIONLIQUID RATE CONTROL*Adjust this number to fit your particular configuration.**If you are using a PWM control valve, some adjustment

202 Firmware Version 5.4LIQUID SERVO SETTINGS DESCRIPTION• Valve Response 1Default Value: 100%Determines the speed of the servo valve when product

203 APPLICATIONLIQUID RATE CONTROL• Allowable ErrorDefault Value: 2%2% - 3% is the normal dead band setting range.- Too low of a setting value can

204 Firmware Version 5.4MISCELLANEOUSGLOSSARY OF APPLICATION SETTINGSConfiguration Settings• Rate Outside of Field Rate that will be used outside o

205 APPLICATIONLIQUID RATE CONTROL• Coverage OptionBased on the coverage option selected, this setting determines the behavior of the swath section

8 Firmware Version 5.4• The display must be readily accessible to the machine operator.• The display must not obstruct the machine operator's

206 Firmware Version 5.4• Zero Flow OffsetRepresents the maximum duty cycle that is sent to the control valve without producing any hydraulic flow

207 APPLICATIONLIQUID RATE CONTROLFERTILIZER DEFAULT PRODUCT SETTINGS Material TypeAbbreviated name for display and predefined name for SMSPercenta

208 Firmware Version 5.4

209 APPLICATIONISOBUS SERIAL APPLICATION RATE CONTROLAPPLICATIONAPPLICATIONISOBUS SERIAL APPLICATION RATE CONTROLENABLE VIRTUAL TERMINAL AND TASK C

210 Firmware Version 5.4Firmware Version 5.4SETUP Select the System Type- Sprayer- SpreaderSelect the Controller Make and Model- Hardi • 5500 (

211 APPLICATIONISOBUS SERIAL APPLICATION RATE CONTROLEnter the Configuration NameInput the number of sectionsNote: The user will have to setup a c

212 Firmware Version 5.4Firmware Version 5.4STATUS SCREENThe status screen provides the user with readout of the connected controller’s target rate

213 APPLICATIONISOBUS SERIAL APPLICATION RATE CONTROLSETTINGS SCREENMANAGE CONFIGURATIONSPress Manage Configurations button in Settings screen.Mana

214 Firmware Version 5.4Firmware Version 5.4Warning Enabled – With this setting enabled, the user will get a “Rate Not Responding” alarm when the a

215 APPLICATIONINJECTIONAPPLICATIONINJECTIONDirectCommand interfaces with the Raven SCS Sidekick™ for complete control over chemical injection appl

9 GENERALINSTALLATIONFUSE INSTALLATION AND REPLACEMENT Fuse Type: Blade Style (ATO/ATC)Rating:Fuse Holder (orange wire) 5A, 250 VACFuse Holder (pin

216 Firmware Version 5.4• Error DelayThe number of seconds that the actual rate falls out of the error threshold before an alarm sounds.Flow Monito

217 APPLICATIONINJECTION7. Enter Actual Dispense AmountEnter in the actual amount of the product that was dispensed. Press to continue.8. Calib

218 Firmware Version 5.43. Acknowledge the WarningA warning appears, stating that you must circulate the product back to the Direct Injection tank

219 APPLICATIONINJECTION • (A) Mapping Toolbox• (B) Product Control Toolbox• (C) Injection Controls button• (D) NORAC UC5 Boom Height Control Optio

220 Firmware Version 5.4Direct Injection: Pump Doesn’t RunPower can be checked at multiple locations. First is the connection at the Injection modu

221 APPLICATIONINJECTIONBATTERY POWER PIN OUTS Direct Injection: Pump Runs Full SpeedDigital Pump Speed Sensor - The injection pump’s digital pump

222 Firmware Version 5.4ANALOG SPEED PIN OUTS Direct Injection: Application ErrorThe injection module requires that a pump calibration be performed

223 APPLICATIONINJECTIONDISCHARGE FLOW SENSOR PIN OUTS Direct Injection: Inlet RestrictionThe injection pump has a vacuum switch that is used to wa

224 Firmware Version 5.4Rate Response Warning• Error ThresholdThe user-defined percentage of actual rate error allowed before an alarm sounds.• Err

225 APPLICATIONNORAC UC5APPLICATIONNORAC UC5NORAC UNLOCKPress: Home button > Setup (wrench) button > Display button > Features tabThe Feat

10 Firmware Version 5.4 An on-screen Keyboard is made available when appropriate for use during all setup processes. Press the keyboard button to a

226 Firmware Version 5.4SETUP CONFIGURATIONPress: Home > Setup (wrench) button > Configuration (tractor) button > Configuration tab > (

227 APPLICATIONNORAC UC5The following settings appear on the General Tab.Minimum Height Mode includes three selections:• Absoluteno sensors are all

228 Firmware Version 5.4RUN CONFIGURATIONOnce a configuration has been completed, the Map View button appears at the bottom of the Home screen. Pre

229 APPLICATIONNORAC UC5Boom Height Control Options ScreenPressing the Boom Height Control Options button (A) opens the Boom Height Control Options

230 Firmware Version 5.4

231 APPLICATIONSPREADERAPPLICATIONSPREADERDirectCommand for spinner spreaders is capable of controlling the product conveyor, spinner speed, monito

232 Firmware Version 5.46. Select Controller DeviceSelect DirectCommand from the Device drop-down menu. Select either, Spinner Spreader Control 3C

233 APPLICATIONSPREADER- If desired, press to enter a different name for your vehicle. Press when complete.15. Drawn SpreaderEnter Implement Na

234 Firmware Version 5.4Spreader Control: PWM Control Valve• PWM FrequencyThe frequency that the PWM control valve is pulsed at. Settings can be fo

235 APPLICATIONSPREADER- Decreasing this value will have the overall effect of speeding up servo valve response.- Increasing this value will have t

11 SETUPCONFIGURATIONSETUPSETUPCONFIGURATIONINITIAL STARTUPAn Initial Setup wizard is presented on startup.Once the wizard is completed, it is not

236 Firmware Version 5.4Beginning with the 5.4 display firmware upgrade, checking the Automatic Control check box exposes a Spinner Icon in the Tas

237 APPLICATIONSPREADER1. Press: Home button > Setup (wrench) button > Configuration (tractor) button > Product tab > Add (+) button &

238 Firmware Version 5.4LOAD CONFIGURATION1. Press: Select Event button.Select a Season, Grower, Farm, and Field on the Management Selection scree

239 APPLICATIONSPREADER4. Select Region and Controlling ProductSelect Region from drop-down menu or use press keyboard button to name region.Selec

240 Firmware Version 5.4SPINNER SPREADER, WITH TWO-BIN CONFIGURATION• Spreader Control buttonDisplays the status of the product control channel. Th

241 APPLICATIONSPREADERNote: For proper machine performance and accuracy, you should check the Product Density daily.• Feed Gate 1 OpeningRepresen

242 Firmware Version 5.4The Conveyor Rate button opens a setup screen where the conveyor rate can be inputted and a table of previously applied pro

243 APPLICATIONSPREADERSpreader Control: Static CalibrationYou must perform a conveyor discharge calibration for each granular product control chan

244 Firmware Version 5.4WARNING: Make sure the spinner is free of material before restarting the spinner hydraulic circuit.12. A warning will app

245 APPLICATIONSPREADER2. Make sure the applicator is inside of the field boundary.Problem: Conveyor turns off in the middle of the pass.Solution:

12 Firmware Version 5.4LOCATION SPECIFIC SETUP1. LanguagePress to continue.2. Unit SystemImperial or MetricPress to continue.3. Date and TimeS

246 Firmware Version 5.4

247 APPLICATIONSTRIP TILLAPPLICATIONSTRIP TILLDirectCommand for Strip-Till applicators monitors bin level and fan speed sensors, maintains an accur

248 Firmware Version 5.47. Select Controller DeviceSelect DirectCommand from the Device drop-down menu. Select Granular Strip-Till Control from th

249 APPLICATIONSTRIP TILL17. Select ImplementPress to continue.18. Select Second ImplementUse drop-down menu to select Implement or press to

250 Firmware Version 5.44. Enter Implement InformationPress and enter implement Make and Model. Press to continue.5. Select Implement Attachm

251 APPLICATIONSTRIP TILL16. Enter Container UnitsUse the drop-down menu to select the container units. Once container has been configured press

252 Firmware Version 5.4Press: Home button > Setup (wrench) button > Configuration (tractor) button > Configuration tab > select your s

253 APPLICATIONSTRIP TILLStrip Till Control: PWM Control Valve• PWM FrequencyThe frequency that the PWM control valve is pulsed at. Settings can be

254 Firmware Version 5.4• Response ThresholdDetermines where the control channel switches between using Actuator Response 1 and Actuator Response 2

255 APPLICATIONSTRIP TILL Actuator/Clutch LogicDetermines Actuator/Clutch Behavior on Zero Rate Fertilizer Blend SetupDry fertilizer blends are set

13 SETUPCONFIGURATIONIMPORT SETUPPress “Import Setup” button then to continue.Select desired setup file from directory. Press to accept the set

256 Firmware Version 5.45. Press to start the process of adding components to the fertilizer blend.Note: Any liquid herbicides set up within th

257 APPLICATIONSTRIP TILLThe Strip Till Control screen appears.Press the Prime button to access the Air Cart Prime screen.The Air Cart Prime screen

258 Firmware Version 5.4The Start Prime button (A) begins the meter prime routine and each meter shaft will rotate the number of revolutions as def

259 APPLICATIONSTRIP TILLStrip Till Control Screen• Product DensityThis density value (shown in pounds per cubic foot, or lb./ft.3), is stored with

260 Firmware Version 5.41. Read Static Calibration warningA warning appears, advising to disable the blower fan circuit and prepare to catch any p

261 APPLICATIONSTRIP TILLPress: Map button > Strip Till Control button > Static Calibration button1. Read Static Calibration warningA warnin

262 Firmware Version 5.42. Enter Actual WeightThe Accumulated Weight is shown in the top portion of the screen. Press to enter the Actual Weight,

263 APPLICATIONSTRIP TILLProblem: AutoSwath feature is not shownSolution: The display must have the AutoSwath feature password-unlocked before th

264 Firmware Version 5.4FERTILIZER DEFAULT PRODUCT SETTINGS Material TypeAbbreviated name for display and predefined name for SMSPercentage (in ter

265 HARVESTHARVEST MONITORING/MAPPINGHARVESTHARVESTHARVEST MONITORING/MAPPINGDISPLAY PREPARATION• Create a backup of your spring information. Go to

14 Firmware Version 5.4IMPORT SETUPPress “Import Setup” button then to continue.Select desired setup file from directory.Press to accept the se

266 Firmware Version 5.43. Input Header OffsetFor combines with offset headers, this compensates for the distance between the center of the vehicl

267 HARVESTHARVEST MONITORING/MAPPINGCAUTION: If Reset All is pressed the sensor will have to be calibrated for all headers!Input Header OffsetIf t

268 Firmware Version 5.41. Run SeparatorStart the separator and feeder house with the proper header attached. Run at full speed.CAUTION: Do not ha

269 HARVESTHARVEST MONITORING/MAPPING1. Measure Moisture on Grain SamplesRandomly sample grain harvested into an active region, then measure moist

270 Firmware Version 5.45. Calibration Load warningRead warning, press when finished.6. Name Load Display will give load a default name of time

271 HARVESTHARVEST MONITORING/MAPPINGWhen performing a Harvest operation, the AutoSwath feature includes sensitivity levels, which compensate for v

272 Firmware Version 5.4 • (A) GPS Status• (B) Total Field Area• (C) Ground Speed• (D) Diagnostics button• (E) Map Legend (varieties)• (F) Legend

273 HARVESTHARVEST MONITORING/MAPPING- If the actual moisture is below the set dry moisture percentage and "Expand Bushels for All Grains Belo

274 Firmware Version 5.4MAP SCREEN: FLOW DELAYWhen the Map screen is running in a Zoom Detail view, instantaneous coverage (A) is shown automatical

275 HARVESTHARVEST MONITORING/MAPPING• Motor CurrentMeasure of Elevator Mount Unit (EMU) current, shown in amps.

15 SETUPCONFIGURATIONUse the scroll bar to find the file you wish to import.When a setup file is created it is saved in a folder titled with the di

276 Firmware Version 5.4

277 HARVESTCLAAS QUANTIMETERHARVESTCLAAS QUANTIMETERThe CLAAS Quantimeter Optical Sensing System includes the option of interfacing with the displa

278 Firmware Version 5.4Note: Adjustment of Combine Settings and the Header Sensor Calibration is performed through the CLAAS CEBIS monitor.• Vehi

279 HARVESTCLAAS QUANTIMETERCreate a new Field Operation Configuration.After you have completed the grain weight calibration and a new calibration

280 Firmware Version 5.4MAP SCREEN FOR CLAAS QUANTIMETEROnce an operating configuration is created for a CLAAS Quantimeter harvest configuration, a

281 HARVESTCLAAS QUANTIMETERNotes:• The Grain Harvest Diagnostics screen displays different information than the Diagnostics screen that appears fo

282 Firmware Version 5.4Possible Cause: The display has detected that the crop type specified in the CEBIS monitor has changed to a crop type that

283 APPENDIXAPPENDIX APPENDIXSYSTEM DIAGRAMS REFERENCETo view detailed system diagrams for various machine configurations, go to the Support tab of

284 Firmware Version 5.4LEGACY FILE FORMATSPRESCRIPTION MAP FILE TYPES• .irxThe .irx file supports multiple product recommendations in a single fil

285 APPENDIX• .msfThe .msf (Management Setup File) file format allows the display to import Grower and Field information from SMS software via the

iii TABLE OF CONTENTSTable of ContentsGeneralAbout this ManualIntroduction and Company Profile...

16 Firmware Version 5.43. Product setupFor more information, see “Product tab” on page 22, as well as the additional configuration information des

286 Firmware Version 5.4personnel constitutes fraud. Ag Leader is not responsible for any damage or loss incurred as a result of access to the lock

287 INDEXIndexAAB/smartpath toggle 115active line cycle 116adaptive curve 110area count 117heading change 117heading threshold 117new pass 117adapt

288 Firmware Version 5.4single motor drive 160gear ratio calculation 160GPS button 16grain harvest diagnostics 274grain settings screen 23grain wei

289 INDEXproduct tab 22add 22crop settings 23delete 22edit 22edit info 23edit legend 23grain settings 23projected path 116proximity sensor 274Rrefe

290 Firmware Version 5.4

17 SETUPCONFIGURATION• Display tabcontains functionality for setting up a Display Owner and making any needed edits to the owner personal informati

18 Firmware Version 5.4• Operating UnitsSelect either Imperial or Metric.• Enable VideoEnables input from up to four video cameras.• ISOBUS Setting

19 SETUPCONFIGURATIONUnlocking FeaturesThe Features Tab is where you can enter unlock codes. Unlock codes are unique to the serial number of each d

20 Firmware Version 5.4Use / to specify a length of time that you wish the display to remain powered up in standby mode after the vehicle power has

21 SETUPCONFIGURATIONCONFIGURATION BUTTONCONFIGURATION TABPress: Home button > Setup (wrench) button > Configuration (tractor) button > Co

22 Firmware Version 5.4PRODUCT TABPress: Home button > Setup (wrench) button > Configuration (tractor) button > Product tabThe Product tab

23 SETUPCONFIGURATIONPlanting Settings• Edit Info buttonPress to edit the following information for the highlighted product in the Product List.- M

24 Firmware Version 5.4For more information, see “Legend Settings” on page 52.

25 SETUPMANAGEMENT SETUPSETUPMANAGEMENT SETUPCONFIGURATION SELECTIONNote: Configuration Setup is specific to an operation (Guidance, Tillage, Plant

iv Firmware Version 5.4Display tab... 18Feat

26 Firmware Version 5.4Some Modules Not Detected Configuration can be loaded but is not detecting all the modules associated with the configuration

27 SETUPMANAGEMENT SETUPEVENTSEvents are used to track field operations. New events can be created at anytime and therefore a physical field can be

28 Firmware Version 5.4Starting an Event1. Press: Select Event button.Select a Season, Grower, Farm, and Field on the Management Selection screen.

29 SETUPMANAGEMENT SETUPThe Event Options screen allows operator to change the Event name, Suspend Event, and to Clear Map bounds.Select a Previous

30 Firmware Version 5.4MANAGEMENT BUTTONPress: Home button > Setup (wrench) button > Management (Barn) buttonFrom this screen the operator ca

31 SETUPMANAGEMENT SETUPFarm and Field In the display, farms are subdivided into fields. You can associate Field names with a particular Grower. If

32 Firmware Version 5.4• Clear Bounds buttonPress to center the map on the current GPS position.Note: The Clear Bounds feature is particularly use

33 SETUPMANAGEMENT SETUPSEASON TABPress: Home button > Setup (wrench) button > Management (Barn) button > Season tabA season is defined as

34 Firmware Version 5.4Add a UserPress: Home button > Setup (wrench) button > Management (Barn) button > User tab > Plus (+) button1.

35 SETUPMANAGEMENT SETUPGeneral tab• First and Last Name• Set and Clear Password• Applicator License• MemoPhone/Email tab• Home Phone• Mobile Phone

v TABLE OF CONTENTSSetup Event...45Field Fi

36 Firmware Version 5.4PERMISSION LEVEL FOR OPERATORSFull PermissionProvides full access to features and functionality on the map and home screen.

37 SETUPMANAGEMENT SETUP Custom PermissionCan allow or deny the following options:• Management screen• Pan/Zoom controls• Legend Toolbox• Marks

38 Firmware Version 5.4Setup and USB buttons are locked for Operators if a Manager is present in the system. A Manager can access setup menu and US

39 SETUPMANAGEMENT SETUPACCESSING SETUP MENUS1. Press Setup (wrench) button.2. Select Manager from drop-down menu. Press .3. Enter password. Pr

40 Firmware Version 5.4Password generator will require the following information:• (A) Display serial number• (B) Major revision- First digit of fi

41 SETUPMANAGEMENT SETUP• Remove buttonPress to remove a business.

42 Firmware Version 5.4

43 SETUPFIELD OPERATIONSSETUPFIELD OPERATIONSA. Operator Selection, see “Operator Selection” on page 43B. Edit Operator, see “User Setup button”

44 Firmware Version 5.42. Choose the operator from drop-down menu.Note: Checkbox will require a password to be entered upon start up of the displa

45 SETUPFIELD OPERATIONSSETUP EVENTYou must have already created the following: • A Season, Grower, Farm and Field in Setup Management. For more in

vi Firmware Version 5.4Speed Input Settings... 72Calib

46 Firmware Version 5.44. Return to Home screenWhen you complete the steps in the Wizard, you will return to the Home screen.• For information on

47 SETUPFIELD OPERATIONSRUN SCREENS • (A) Status Bar• (B) On-screen Light bar• (C) Mapping toolbox• (D) Mapping Function tabs• (E) Product Control

48 Firmware Version 5.4Note: For more information on the Video screen, see “Video” on page 62.AutoSwath button. Pressing this button turns the Aut

49 SETUPFIELD OPERATIONSEngage - Not ReadyGrey with a red circle and slash if the autosteer system is off and unable to engage.Note: For more info

50 Firmware Version 5.4Vehicle Icon - Zoom to ExtentThe Vehicle Icon is shown by an arrow inside a circle if the Map screen is viewed in Zoom to Ex

51 SETUPFIELD OPERATIONSMap Legend tabPress the Map Legend button at the top of the Mapping Toolbox, and the Legend appears. User can choose betwee

52 Firmware Version 5.4Select the Autoswath channel to apply the reference map toNot selecting a channel will load the reference map as a visual on

53 SETUPFIELD OPERATIONS• Color SchemeThe Color Scheme can be modified by using the drop-down list. Choices include the following:- Green-Yellow-Re

54 Firmware Version 5.4• If you have numerous map icons, you can cycle through them by pressing /.• When creating or editing a marker, check the Ge

55 SETUPFIELD OPERATIONSBoundary SettingsUnderneath the Boundary Type area, you have the choice of creating either an Outer Boundary or an Inner Bo

vii TABLE OF CONTENTSSatellite Plot...103GPS Information

56 Firmware Version 5.4HEADLANDSPress the Headlands button on the Field tab to access the Headland Options screen.A Field Boundary is required to c

57 SETUPFIELD OPERATIONSHeadland TypesAll-AroundOffset Implement Width - number of implement widths used to set the headland widthOffset Distance -

58 Firmware Version 5.45. Save, Resume, or Discard• Save-a. Press Save button-b. Default name is time and date. Press to change name.-c. Press

59 SETUPFIELD OPERATIONSHeadland Alarm SettingsPress Headland Alarm Settings button. Alert Distance - distance from approaching headland at which

60 Firmware Version 5.4Setup Map ScreenTopography screenNew Survey button - press to create a new elevation surveyAdd to Selected button - press to

61 SETUPFIELD OPERATIONSIf you have RTK GPS reception, you are allowed to collect an elevation survey. This will allow you to collect the Lat/Long

62 Firmware Version 5.4During collection of an elevation survey, points will be logged to the file every 3 meters. An onscreen visual will appear i

63 SETUPFIELD OPERATIONS• BrightnessPress / to increase or decrease the brightness of the video input.• ContrastPress / to increase or decrease the

64 Firmware Version 5.4

65 SETUPEXTERNAL DRIVESETUPEXTERNAL DRIVEEXTERNAL STORAGE OPERATIONSThe External Storage Operations button is where you can copy your field data; u

viii Firmware Version 5.4Save ... 120

66 Firmware Version 5.4• Marker Sets and MarkersNote: Do not use the IBK to “clone” a display. Use AGSETUP..AGDATA• Includes all the necessary dat

67 SETUPEXTERNAL DRIVE• Equipment Used• Products Used• Marks Logged• Boundaries• Guidance Patterns• Flexible export options• Will be able to export

68 Firmware Version 5.4 Press to Export All Log filesExport All Log Files

69 SETUPDEVICESSETUPDEVICESDEVICE INFORMATIONPressing on the Device Information button, located in the upper right corner of the display, opens the

70 Firmware Version 5.4

71 SETUPSETTINGSSETUPSETTINGSEQUIPMENT SETTINGS Press the Configuration Settings button on the Configuration Setup screen to view or edit the name

72 Firmware Version 5.4Equipment Configuration Settings for Rate ControlIf you are using an operating configuration with Rate Control, (such as for

73 SETUPSETTINGSThe Speed Input Settings screen is where you can calibrate the ground speed input for accurate speed and area calculations.In most

74 Firmware Version 5.4Press: Home button > Setup (wrench) button > Configuration (tractor) button > Configuration tab > your specific

75 SETUPSETTINGS• Reset All. This button resets the settings to defaults.AUXILIARY INPUT SETTINGSPress: Home button > Setup (wrench) button >

ix TABLE OF CONTENTSPlantingCreate Planting ConfigurationCreate Equipment Configuration...

76 Firmware Version 5.4The Auxiliary Input Diagnostics screen lists the active switches. These color-coded boxes display the following diagnostics:

77 SETUPSETTINGS- The Minimize Skip option turns off the implement section after the entire section is fully inside your coverage area. This preven

78 Firmware Version 5.4ANTENNA OFFSETS TABAt the Antenna Tab, enter the distance from locations on the vehicle to the antenna.• Measure and enter t

79 SETUPSETTINGSSection Offsets• Press the first to enter the distance that the swath section is located from the hitch point. • Press the second

80 Firmware Version 5.4

81 SETUPVIRTUAL TERMINALSETUPVIRTUAL TERMINALThe display is compatible with the ISO 11783 (ISOBUS) Virtual Terminal Standard. This enables support

82 Firmware Version 5.4Once a Virtual Terminal has been enabled will appear in the task bar. Toggle between the Virtual Terminal run screen and o

83 SETUPVIRTUAL TERMINALIf there are multiple ISO implements connected, press the VT button to toggle between Working Sets.The Working Sets can a

84 Firmware Version 5.4Assign implement functions to ISO compatible inputs.The number of functions and inputs shown on the Auxiliary Mappings scree

85 SETUPVIRTUAL TERMINAL Pressing the Diagnostics button on the Devices screen brings up the ISO Node Diagnostics screen which shows the following